![]() Unlike some vendors, Dell’s fans use a removable cage surrounding an industry-standard fan. The Good News: It’s Easy to Swap the Fans Some models will wait for the user to hit a key to acknowledge that error, and I don’t want that happening – I leave my servers in the closet without a monitor attached. If you don’t get fans that are PWM-controlled, then the Dell motherboard will freak out upon boot-up and think there’s no fans connected. I highly recommend these Artic F9 PWM 92MM fans. I bought six quiet 92mm PWM-controlled fans for under $10 each that: Quiet-PC freaks like me turn to fans that turn slower, yet still push a lot of air. Have pulse width modulation (PWM) speed control – the motherboard can control the fan speed based on how hot the server getsįans like this rely on very fast rotation speeds to push a lot of air, but the faster the blade spins, the more noise it makes.Scream at 57 decibels – not quite as loud as yo momma, but close.Move up to 150 cubic feet of air per minute.The stock fans are Nidec BetaV TA350DC 92mm fans that: I can’t run cables inside the walls since it’s a rented condo, and I can’t run cables along the floor because I’ve got a girlfriend with a keen sense of design. ![]() This wasn’t a problem when I had the server in the basement, but now that I’ve moved to Chicago and my “datacenter” is my home office closet, it’s a problem. I couldn’t carry on a conversation next to this server, let alone record a podcast. They’re temperature-controlled, so they don’t go full blast unless the server’s working hard, but even at very light loads they’re just way too loud. It’s got 6 92mm fans that can wake the dead. Seriously, the case is bulletproof and gawdawful heavy.īut it’s loud. Two quad-core CPUs, 16gb of memory, six SATA drives in a RAID 10, and about a hundred pounds of solid steel. Quest got me a Dell PowerEdge 1900 to use as a virtualization host, and it’s been great. I’ve blogged about how to build a silent PC, but today I’m tackling another noisy beast – an off-the-rack server. I like running my lab out of my office closet, but I don’t want to hear any of them running. ![]() On my similar 3rd gen, i will see about breaking the Raid 1, by removing 1 drive, and installing/importing the single disk into the new system.I’ve got a few servers in my home lab and I’ve always taken steps to make sure they’re quiet. 1 works, and has been in production for about a year now, the other 3 do not boot. I in fact have 1 confirmed 3rd Gen 1950, with the same exact components (CPU, RAM, HDDs, Raid Controller), as 3 others. Some say PERC isn't supported - That seemed to be related to much much older versions of FreeBSD and pfSense, as again i have a 2nd gen and 3rd gen that are in production and working properly. No change, still tries to load/detect FD0 Though i did try and change from 4 cores to 2 cores, no change.Įscape to Loader Prompt and use the "hint." to disable Floppy. maybe last resort, but that doesn't seem to be likely. Uninstall 1 CPU - Did not try, since i have other servers with 2x CPUs. No FD installed, nor anywhere in BIOS to disable.ĭisable ACPI in BIOS, and boot PF with no ACPI - Tried no change. I have ready many many posts, that say to try the following:ĭisable Floppy drive in BIOS. Sorry i meant to add a bit more before submitting… I'm really at a loss, any guidance would be much appreciated. Uart0: port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0Īnother Working System (most like the non-working server): Note: The next message displayed after "device_attach: fdc0 attach returned 6" is: Server was built with "pfSense-2.0.1-RELEASE-amd64", and has been upgraded and currently running to "pfSense-LiveCD-2.1.5-RELEASE-amd64" Last message when system hangs on boot : IPsec: Initialized Security Association Processing. Last message when system hangs on boot : device_attach: fdc0 attach returned 6 No matter which ISO i use, the results are the same. (details below:)įailing System (actually 3 different systems, all with identical hardware…) I do however, have a few Dell PowerEdge 1950 II and III servers that are running PFSense just fine. I am currently having an issue getting PFSense to install on some of my Dell PowerEdge 1950 III servers.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |